How To Bleed A Radiator Jeep Dodge 4 7l Youtube The process for bleeding the radiator on a jeep dodge 4.7l v* is not the same as in most vehicles. improper bleeding of air from the syste, can lead to overh. How to bleed air out of the coolant system on a dodge jeep 4.7l engine after replacing a water pump radiator or antifreeze hosethis was on a 2007 commander#b.
Burp Bleed Coolant System 4 7l Dodge Jeep How To Youtube If you can't remove the air bleed fitting for the cooling system of the 3.7 and 4.7l chrysler, dodge, jeep, and mitsubishi this is an easy mod that can be ma. Once the bit breaks through the plug, the coolant rushing out will displace the metal shavings. once the plug is out, use the magnet to get any stray metal in the coolant. i use a piggy back set up now. 3 8" pipe thread (with anti seeze) that is drilled and tapped for a 1 4" pipe thread plug in the center of it (which is also anti seezed) and. Fill radiator with coolant via radiator cap. 2. fill engine block with coolant via bleed plug. 3. leave bleed plug off and start engine, when bubbles stop appearing screw plug back in. 4. when it reaches operating temp shut off. 5. keep coolant reservoir full, cause engine will draw in coolant when it cools. Lisle 24680 spill free funnel is the only way i use to bleed cooling systems, it simply works. crank the heat to full open and let idle till the thermostat opens at least once. you can pump the hoses during that time carefully and help speed up the process but still wait till the stat opens. reply like.
Dodge Chrysler Jeep 3 6 Pentastar How To Bleed Cooling System Youtube Fill radiator with coolant via radiator cap. 2. fill engine block with coolant via bleed plug. 3. leave bleed plug off and start engine, when bubbles stop appearing screw plug back in. 4. when it reaches operating temp shut off. 5. keep coolant reservoir full, cause engine will draw in coolant when it cools. Lisle 24680 spill free funnel is the only way i use to bleed cooling systems, it simply works. crank the heat to full open and let idle till the thermostat opens at least once. you can pump the hoses during that time carefully and help speed up the process but still wait till the stat opens. reply like. (formerly daveb673) avatar is from the center of the whirlpool galaxy 2007 inferno red quad cab 4.7l flex fuel 2wd w 545rfe leer xr topper filtermag ss375 e fan install (now taurus 3.8 fan) 3.5 inch steel pipe intake and "basking shark" filter box powertrax lock rite transgo shift kit a c heater valve mod (deleted) ho cams and now a cabin air filter!!. So get home, jack the front up or park the front on a set of ramps, let it cool. take the rad cap off and start and get to temp, squeeze the top hose a few times wait for level to drop. add antifreeze as needed. let jeep sit over night and do again in the morning. do again in the afternoon if you can or the next night.
How To Bleed A Radiator Youtube (formerly daveb673) avatar is from the center of the whirlpool galaxy 2007 inferno red quad cab 4.7l flex fuel 2wd w 545rfe leer xr topper filtermag ss375 e fan install (now taurus 3.8 fan) 3.5 inch steel pipe intake and "basking shark" filter box powertrax lock rite transgo shift kit a c heater valve mod (deleted) ho cams and now a cabin air filter!!. So get home, jack the front up or park the front on a set of ramps, let it cool. take the rad cap off and start and get to temp, squeeze the top hose a few times wait for level to drop. add antifreeze as needed. let jeep sit over night and do again in the morning. do again in the afternoon if you can or the next night.
How To Bleed A Radiator Youtube
Comments are closed.