Mazda 3 Service Manual Refrigerant Pressure Sensor Removal

Mazda 3 Service Manual Refrigerant Pressure Sensor Removal 4. loosen the refrigerant pressure sensor using two spanners. 5. remove the refrigerant pressure sensor tightening torque. 10—11 n·m {102—112 kgf·cm, 89—97 in·lbf} 6. install in the reverse order of removal. 7. perform the refrigerant system performance test refrigerant pressure sensor installation note. 1. 1. disconnect the negative battery cable. 2. discharge the refrigerant from the system. (see refrigerant recovery .) (see refrigerant charging .) 3. loosen the refrigerant pressure switch using two spanners. 4. remove in the order indicated in the table.

Mazda 3 Service Manual Refrigerant Pressure Sensor Inspect Mazda 3 service manual hvac a c heater, ventilation and air conditioning. abbreviation. a c. air conditioning. features. the full auto air conditioner has been adopted for vehicles with skyactiv g 2.0. specifications. full auto air conditioner. basic system. Page 34: after repair procedure [z6] mazda 3 workshop manual – engine wiring diagrams diagnostic trouble codes after repair procedure [z6] b3e010200102w20 1. connect the wds or equivalent to the dlc 2. 2. cycle the ignition switch off, then to the on position (engine off). page 35: obd drive mode [z6] 3. idle the engine for more than 120. The refrigerant pressure sensor is typically mounted to the a c pressure line, compressor, or accumulator drier. step 2: disconnect the negative battery cable. disconnect the negative battery cable with a wrench of ratchet and set it aside. step 3: remove the sensor electrical connector. step 4: remove the sensor. Refrigerant pressure check [(us)] . s)]id0710003002x1id0710003002. 1install the manifold gauge set. (s. manifold gauge s. connection.)start the engine. r (with active air shutter): openwait for. d ambient temperature for 2 min.verify that there are high low pressure value readings with. v g 2.5 (hfc 134a)am3zzw00032037• if not as verified.

Mazda 3 Service Manual Pressure Sensor Removal Installatio The refrigerant pressure sensor is typically mounted to the a c pressure line, compressor, or accumulator drier. step 2: disconnect the negative battery cable. disconnect the negative battery cable with a wrench of ratchet and set it aside. step 3: remove the sensor electrical connector. step 4: remove the sensor. Refrigerant pressure check [(us)] . s)]id0710003002x1id0710003002. 1install the manifold gauge set. (s. manifold gauge s. connection.)start the engine. r (with active air shutter): openwait for. d ambient temperature for 2 min.verify that there are high low pressure value readings with. v g 2.5 (hfc 134a)am3zzw00032037• if not as verified. Start the engine. turn on the ac and set it to the coldest setting, and the fan speed to maximum. remove the cap from the low pressure service port labelled l, and connect the ac recharge kit. note: if the ports are not labelled, try connecting the recharge kit to both unlabeled ports on the ac hoses. the recharge kit will only properly connect. Remove the column cover. (refer to the 1996 626 mx 6 workshop manual, section s.) 2. measure the voltage at the terminals of the windshield wiper and washer switch connector with the wiper switch in the following positions. page 119 (refer to page d 12) step 3 1. remove the column cover.

Mazda 3 Service Manual Pressure Sensor Removal Installatio Start the engine. turn on the ac and set it to the coldest setting, and the fan speed to maximum. remove the cap from the low pressure service port labelled l, and connect the ac recharge kit. note: if the ports are not labelled, try connecting the recharge kit to both unlabeled ports on the ac hoses. the recharge kit will only properly connect. Remove the column cover. (refer to the 1996 626 mx 6 workshop manual, section s.) 2. measure the voltage at the terminals of the windshield wiper and washer switch connector with the wiper switch in the following positions. page 119 (refer to page d 12) step 3 1. remove the column cover.